Accessories

Button Switch Set

799.00

IR Kit for Arduino

499.00

Servo Motor - Metal Gear Servo, MG996R

449.00

Micro Servo Motor - Metal Gear, 180, MG90

399.00

Servo Motor - Metal Gear, 180, MG995

349.00

Servo motor Plastic Gear SG90

179.00

DC Motor

159.00

Atmega 16U2 USB Controller IC

149.00

Battery Holder 6 AA with DC Jack

119.00

BO Motor with Wheel

119.00

Push Button Switch

99.00

Alligator Connectors

99.00

LEDs - Blue

99.00

LEDs - Green

99.00

Jumper Wires - M-M

99.00

Jumper Wires - M-F

99.00

Jumper Wires - F-F

99.00

LEDs - Red

99.00

RGB LEDs

99.00

BO Motor, 150 RPM

99.00

LEDs - Yellow

99.00

LEDs - White

99.00

Battery Holder 4 AA with DC Jack

89.00

Breadboard - 800 Points

89.00

 Bread Board - 400 points

89.00

USB Cable - Type A-to-Mini B

49.00

Piezoelectric Plate

49.00

Vibration Motor

49.00

USB Cable A-B for Arduino

49.00

Buzzer Big 5V

29.00

Buzzer Small 5V

19.00

9V Battery - HIW

19.00

9V Battery connector with DC Jack

19.00

IR Kit for Arduino

IR Kit for Arduino

 499.00

IR is widely used in remoter control. With this IR receiver, the Arduino project is able to receive command from any IR remoter controller if you have the right decoder. Well, it will be also easy to make your own IR controller using IR transmitter.

USB Cable - Type A-to-Mini B

USB Cable - Type A-to-Mini B

 49.00

USB Mini Cable is mainly used for Arduino Nano (USB 2.0 A to USB 2.0 Mini B) with Gold Plated Connector is the plug-and-play connection cable with MP3 players, digital cameras and PDAs, External Hard Drives. 
It connects speed-critical devices, such as external hard drives and smartphones, and peripherals that require a Mini-B connection to your computer.


FEATURES:
•  Up to 480 Mbps data transfer rate
•  3-foot-long high-speed USB 2.0 A-Male to Mini-B cable
•  Constructed with corrosion-resistant, gold-plated connectors for optimal signal clarity and shielding to minimize interference

Buzzer Small 5V

Buzzer Small 5V

 19.00

5V PCB Mounting Buzzer is a small PCB (printed circuit board) mountable buzzer. It is very small and compact 2-pin structure hence can be easily used on breadboard, PCBs which makes this a widely used component in most electronic applications. This Buzzer module emits loud sound when 3V to 5V is applied to it. Unlike a plain piezo, this buzzer does not need an AC signal. On one hand, that makes it really great for integrating into projects because you don't need an oscillating control signal. But on the other hand, you cannot change the frequency.
 

Buzzer Big 5V

Buzzer Big 5V

 29.00

5V PCB Mounting Buzzer is a big PCB (printed circuit board) mountable buzzer. It is very big and compact 2-pin structure hence can be easily used on breadboard, PCBs which makes this a widely used component in most electronic applications. This Buzzer module emits loud sound when 3V to 5V is applied to it. Unlike a plain piezo, this buzzer does not need an AC signal. On one hand, that makes it really great for integrating into projects because you don't need an oscillating control signal. But on the other hand, you cannot change the frequency.
 

Push Button Switch

Push Button Switch

 99.00

A push-button (also spelled pushbutton) or simply button is a simple switch mechanism for controlling some aspect of a machine or a process. Buttons are typically made out of hard material, usually plastic or metal. The surface is usually flat or shaped to accommodate the human finger or hand, so as to be easily depressed or pushed. Buttons are most often biased switches, although many un-biased buttons (due to their physical nature) still require a spring to return to their un-pushed state. Terms for the "pushing" of a button include pressing, depressing, mashing, slapping, hitting, and punching.

Qty: Pack of 100 switches

Atmega 16U2 USB Controller IC

Atmega 16U2 USB Controller IC

 149.00

The ATmega8U2/16U2/32U2 is a low-power CMOS 8-bit microcontroller based on the AVR enhanced RISC architecture. By executing powerful instructions in a single clock cycle, the ATmega8U2/16U2/32U2 achieves throughputs approaching 1 MIPS per MHz. allowing the system designed to optimize power consumption versus processing speed.

Battery Holder 6 AA with DC Jack

Battery Holder 6 AA with DC Jack

 119.00

A 6 AA is the best suitable power supply option for robotics and embedded system. It comes with DC Jack male connector and is compatible with 6 batteries, the Battery size is AA and provides DC Power supply of 9V and can be directly connected with MehcanzO remote & controller card.

Features 

6 AA Battery Holder with lead wires

Battery Holder 4 AA with DC Jack

Battery Holder 4 AA with DC Jack

 89.00

Battery holder 4 AA is best suitable power supply option for robotics and embedded system. It comes with DC Jack male connector which can be directly connected with MehcanzO remote & controller card.


FEATURES:-
•    It is compatible with 4 batteries.
•    Battery size is AA.
•    DC Power supply of 6V can be given at a time.


 

Alligator Connectors

Alligator Connectors

 99.00

Alligator connector is a sprung metal clip with long, serrated jaws which is used for creating a temporary electrical connection. This simple mechanical device gets its name from the resemblance of its jaws to that of an alligator's or crocodile's. It is used to connect an electrical cable to a battery or some other component. Functioning much like a spring-loaded clothespin, the clip's tapered, serrated jaws are forced together by a spring to grip an object. When manufactured for electronics testing and evaluation, one jaw of the clip is typically permanently crimped or soldered to a wire, or is bent to form the inner tubular contact of a 4 mm female banana jack, enabling quick non-permanent connection between a circuit under test and laboratory equipment or to another electrical circuit. The clip is typically covered by a plastic shroud or "boot" to prevent accidental short-circuits.

9V Battery - HIW

9V Battery - HIW

 19.00

9V BATTERY CLIPac GENERAL DESCRIPTION. 9-volt battery in its most common form was introduced for the early transistor radios. It has a rectangular prism shape with rounded edges and a polarized snap connector at the top. This type is commonly used in walkie talkies, clocks and smoke detectors.

LEDs - Blue

LEDs - Blue

 99.00

A light-emitting diode (LED) is a semiconductor light source that emits light when current flows through it. Electrons in the semiconductor recombine with electron holes, releasing energy in the form of photons. The color of the light (corresponding to the energy of the photons) is determined by the energy required for electrons to cross the band gap of the semiconductor.

It is pack of 100 LEDs

9V Battery connector with DC Jack

9V Battery connector with DC Jack

 19.00

This simple cable has so many uses Plug the battery clip onto a standard 9V battery and connect the other end to any device that needs 9V. The Connector leads are polarity color coded, Red and Black.

FEATURES

  • Red and black leads.
  • DC power jack

LEDs - Green

LEDs - Green

 99.00

A light-emitting diode (LED) is a semiconductor light source that emits light when current flows through it. Electrons in the semiconductor recombine with electron holes, releasing energy in the form of photons. The color of the light (corresponding to the energy of the photons) is determined by the energy required for electrons to cross the band gap of the semiconductor.

It is pack of 100 LEDs

Piezoelectric Plate

Piezoelectric Plate

 49.00

A piezoelectric plate is a device that uses the piezoelectric effect to measure pressure, acceleration, strain or force by converting them to an electrical charge. Piezoelectricity is the electricity generated by piezo element by effect called the piezoelectric effect. It is the ability of certain materials to generate an AC (alternating current) voltage when subjected to mechanical stress or vibration, or to vibrate when subjected to an AC voltage, or both. The most common piezoelectric material is quartz. Certain ceramics, Rochelle salts, and various other solids also exhibit this effect. 


Specification:
•    Resonance Frequency: 4.6 KHz +/- 0.5 KHz
•    Resonance Impedance: 200 Ohms
•    Capacitance: 20nF +/- 30% at 1 KHz
•    Operating Temperature -20 to +70 C
•    Storage Temperature -30 to +80 C
•    Metal Material Brass


Qty: Pack of 5 Pcs.

DC Motor

DC Motor

 159.00

A DC motor is any of a class of rotary electrical machines that converts direct current electrical energy into mechanical energy. The most common types rely on the forces produced by magnetic fields. Nearly all types of DC motors have some internal mechanism, either electromechanical or electronic; to periodically change the direction of current flow in part of the motor.
The DC Motor or Direct Current Motor to give it its full title, is the most commonly used actuator for producing continuous movement and whose speed of rotation can easily be controlled, making them ideal for use in applications were speed control, servo type control, and/or positioning is required. A DC motor consists of two parts, a “Stator” which is the stationary part and a “Rotor” which is the rotating part.

 

Normal DC motors have almost linear characteristics with their speed of rotation being determined by the applied DC voltage and their output torque being determined by the current flowing through the motor windings. The speed of rotation of any DC motor can be varied from a few revolutions per minute (rpm) to many thousands of revolutions per minute making them suitable for electronic, automotive or robotic applications. By connecting them to gearboxes or gear-trains their output speed can be decreased while at the same time increasing the torque output of the motor at a high speed.
 

Servo Motor - Metal Gear, 180, MG995

Servo Motor - Metal Gear, 180, MG995

 349.00

Since MG995 is a servo motor providing precise rotation over 180º range its applications are many and amongst them a few are stated below:

  • The servo is suited for designing robotic arm in which wear and tear of motor is high. Being metal geared, the servo has long life and can be installed on system like robotic arm were motor work is huge.
     
  • The servo is also suited to be used in drones and toy planes. Having a satisfying torque which is enough to overcome air resistance and control wings of plane, the servo is preferred in toy planes and drones which need precision control no matter the condition.

 

Micro Servo Motor - Metal Gear, 180, MG90

Micro Servo Motor - Metal Gear, 180, MG90

 399.00

MG90S servo, Metal gear with one bearing Tiny and lightweight with high output power, this tiny servo i Helicopter, Quad copter or Robot durability. Servo can rotate approximately 180 degrees (90 in each direction), and works just like the standard kinds but smaller. You can use any servo code, hardware or library to control these servos. Good for beginners who want to make stuff move without building a motor controller with feedback & gear box, especially si (arms) and hardware.

Specifications:

• Weight: 13.4 g

 • Dimension: 22.5 x 12 x 35.5

• Stall torque: 1.8 kgf-cm (4.8V)

• Operating speed: 0.1s/60 degree

• Operating voltage: 4.8 V –

• Dead band width: 5 µs

MG90S servo, Metal gear with one bearing Tiny and lightweight with high output power, this tiny servo i Helicopter, Quad copter or Robot durability. Servo can rotate approximately 180 degrees (90 in each direction), and works just like the standard kinds but smaller. You can use any servo code, hardware or library to control these servos. Good for beginners who want to make stuff move without building a motor controller with feedback & gear box, especially si (arms) and hardware.

Specifications:

• Weight: 13.4 g

 • Dimension: 22.5 x 12 x 35.5

• Stall torque: 1.8 kgf·cm (4.8V)

• Operating speed: 0.1 s/60 degree

• Operating voltage: 4.8 V –

• Dead band width: 5 µs

Servo Motor - Metal Gear Servo, MG996R

Servo Motor - Metal Gear Servo, MG996R

 449.00

This High-Torque MG996R Digital Servo features metal gearing resulting in extra high 10kg stalling torque in a tiny package. It features upgraded shock-proofing and a redesigned PCB and IC control system that make it much more accurate than its predecessor MG995. The gearing and motor have also been upgraded to improve dead bandwidth and centering. This high-torque standard servo can rotate approximately 120º (60º in each direction). 
 

Jumper Wires - M-M

Jumper Wires - M-M

 99.00

Jumper wires are simply wires that have connector pins at each end, allowing them to be used to connect two points to each other without soldering. Jumper wires are typically used with breadboards and other prototyping tools in order to make it easy to change a circuit as needed.Male ends have a pin protruding and can plug into things, while female ends do not and are used to plug things into. Male-to-male jumper wires are the most common and what you likely will use most often. When connecting two ports on a breadboard, a male-to-male wire is what you'll need.
 

Jumper Wires - M-F

Jumper Wires - M-F

 99.00

Jumper wires are simply wires that have connector pins at each end, allowing them to be used to connect two points to each other without soldering. Jumper wires are typically used with breadboards and other prototyping tools in order to make it easy to change a circuit as needed.Male ends have a pin protruding and can plug into things, while female ends do not and are used to plug things into. Male-to-female jumper wires are the most common and what you likely will use most often. When connecting two ports on a breadboard, a male-to-female wire is what you'll need.
 

Jumper Wires - F-F

Jumper Wires - F-F

 99.00

Jumper wires are simply wires that have connector pins at each end, allowing them to be used to connect two points to each other without soldering. Jumper wires are typically used with breadboards and other prototyping tools in order to make it easy to change a circuit as needed.
Female ends have a pin protruding and can plug into things, while female ends do not and are used to plug things into. Female-to-female jumper wires are the most common and what you likely will use most often. When connecting two ports on a breadboard, a female-to-female wire is what you'll need.

 

Vibration Motor

Vibration Motor

 49.00

A vibrating motor is essentially a motor that is improperly balanced. In other words, there is an off-centred weight attached to the motor's rotational shaft that causes the motor to wobble. 
The amount of wobble can be changed by the amount of weight that you attach, the weight's distance from the shaft, and the speed at which the motor spins.

This type of motor can be affixed to all kinds of objects, which will cause them to vibrate and move freely about. This is a quick and dirty way to get a Simple Bot to move about, but not exactly the most elegant. Vibrating motors can be found inside cell phones, pagers, gaming controllers, and personal massagers.
In absence of those, you can easily build your own vibrating motor by attaching any off centred weight to any motor shaft. They can also be created by breaking in half balanced components already attached to motor shafts.

 

LEDs - Red

LEDs - Red

 99.00

A light-emitting diode (LED) is a semiconductor light source that emits light when current flows through it. Electrons in the semiconductor recombine with electron holes, releasing energy in the form of photons. The color of the light (corresponding to the energy of the photons) is determined by the energy required for electrons to cross the band gap of the semiconductor.

It's a box of 100 LEDs

 

Breadboard - 800 Points

Breadboard - 800 Points

 89.00

A breadboard is a solderless device for temporary prototype with electronics and test circuit designs. Breadboards are used for rapid prototyping of electronic projects, without needing to solder the components to make it work. Most electronic components in electronic circuits can be interconnected by inserting their leads or terminals into the holes and then making connections through wires where appropriate. The breadboard has strips of metal underneath the board and connects the holes on the top of the board.

This is a Full size breadboard or standard size breadboard with 800 tie points, the breadboard measures 55mm x 170mm, you can combine two or more of this breadboard to make larger or wider breadboards, it also includes an adhesive foam at the back, to mount it securely on most surfaces.

RGB LEDs

RGB LEDs

 99.00

RGB LED means red, blue and green LEDs. RGB LED products combine these three colors to produce over 16 million hues of light. Note that not all colors are possible. Some colors are outside the triangle formed by the RGB LEDs also, pigment colors such as brown or pink are difficult, or impossible, to achieve. RGB LED is a combination of three LEDs in just one package: red, green and blue. You can generate different colors by adjusting the brightness of each of the three LEDs of the RGB LED; to adjust the brightness of each LED, you use a PWM signal.

 

 Bread Board - 400 points

Bread Board - 400 points

 89.00

Solderless breadboards are commonly used for prototyping because they allow you to quickly build temporary circuits without soldering. Breadboards accept most through-hole parts and up to 22 wire. When you’re done or want to change your circuit, it’s easy to take your circuit apart. Pre-cut and premium jumper wires are especially convenient for Solderless Breadboard.Two sides of the breadboard have tabs and the other two sides have compatible slots, which lets you connect multiple 400-point breadboards for more prototyping space.


Specifications:

  • It has total 400 holes
  • Perfect for electronics protype experiments
  • After experimenting with breadboards you can make your circuit more permanent with same connection
  • Made up of ABS plastic + Phosphor bronze nickel plated spring clips.

BO Motor with Wheel

BO Motor with Wheel

 119.00

The wheel is made up of high-quality rubber which gives maximum traction while operating. The wheel is strong and sturdy as it features nylon reinforced plastic rim. This wheel can be coupled to BO type motors by coupling it.

BO motor attached to the shaft, which is mechanically commutated electric motor powered from direct current (DC). Generally used in DIY projects, Battery operated toys, Radio controlled vehicles, Robotic projects etc.

Features:

  • Working voltage of motor: 3-6V
  • High Quality wheels with solid grip tyres
  • Center hole of wheel: 5.3MM x 3.66MM
  • Wheel size: 65x26mm
  • Reduction Rate : 48:1
  • Motor Weight : 50g
  • Color: Yellow

BO Motor, 150 RPM

BO Motor, 150 RPM

 99.00


This is a standard low cost low voltage durable Dual Shaft Plastic Gear BO Motor running at 150 RPM. It is most suitable for light weight robot running on voltages between 5V-9V. Out of its two shafts one shaft can be connected to wheel, while the other can be connected to an encoder.

Features:

  • Gear materials: plastic
  • Motor types: Permanent Magnet
  • Brush-type: Brushed
  • Magnet types: Ferrite Magnets
  • Torque multiplication: Generates a large force at a low speed
  • Low density: Lightweight and Low Inertia
  • Uniformity of parts
  • Capability to absorb shock and vibration as a result of elastic compliance
  • Ability to operate with minimum or no lubrication, due to inherent lubricate
  • Relatively low coefficient of friction
  • Corrosion-resistance; elimination of plating, or protective coatings
  • Consistency with trend to greater use of plastic housings and other components

USB Cable A-B for Arduino

USB Cable A-B for Arduino

 49.00

Use it to connect Arduino Uno, Arduino Mega 2560,Arduino 101 or any board with the USB female A port of your computer. Cable lenght is approximately 178cm. Cable color and shape may vary slightly from image as our stock rotates. USB cable type A/B Standard USB 2.0 cable.

LEDs - Yellow

LEDs - Yellow

 99.00

A light-emitting diode (LED) is a semiconductor light source that emits light when current flows through it. Electrons in the semiconductor recombine with electron holes, releasing energy in the form of photons. The color of the light (corresponding to the energy of the photons) is determined by the energy required for electrons to cross the band gap of the semiconductor.

">

LEDs - White

LEDs - White

 99.00

A light-emitting diode (LED) is a semiconductor light source that emits light when current flows through it. Electrons in the semiconductor recombine with electron holes, releasing energy in the form of photons. The color of the light (corresponding to the energy of the photons) is determined by the energy required for electrons to cross the band gap of the semiconductor.

Button Switch Set

Button Switch Set

 799.00

A push-button (also spelled pushbutton) or simply button is a simple switch mechanism for controlling some aspect of a machine or a process. Buttons are typically made out of hard material, usually plastic or metal. The surface is usually flat or shaped to accommodate the human finger or hand, so as to be easily depressed or pushed. 

Servo motor Plastic Gear SG90

Servo motor Plastic Gear SG90

 179.00

This analog micro servo will rotate up to 180 degrees (90 in each direction). You can expect it to operate the same as standard versions, but this micro servo is much smaller and can fit into tighter spaces. Its lightweight (9g) design will still output a high amount of power. This servo will work with any servo library, code, or compatible hardware.