Female Berg Strip

 99.00

This 40 Pin Female Berg Strip and are designed for soldering directly into printed circuit boards (PCB). They are supplied best for extension of pins of Microcontrollers and ICs.
This is 40 pin single row female berg strip/header which can be cut into sizes with the wire cutter. The pitch for this header is standard 2.54mm.

Specifications & features include:-
•    Standard 0.1" Spacing
•    Nickel-Tin Plated
•    Current Rating up to 1A
•    Gold Plated
•    Ideal for Board Connectors

Pack of 10 Pcs.
•    Temperature Range: -55oC to +105oC
•    Ideal for Connecting 2 Boards Together

Male Berg Strip

 99.00

This 40 Pin Male Berge Strip has the industry standard spacing of 2.54mm and are designed for soldering directly into printed circuit boards (PCB). They are supplied best for extension of pins of Microcontrollers and ICs. These are the connectors used to take input or give output with the help of wires. They can be cut according to the need with the help of wire cutter.

Specifications: 

•    Number of Pins: 40
•    Pin Spacing: 0.1" (2.54 mm)
•    Strip Length: 10.25cm
•    Strip width : ~2.5 mm

Pack of 10 strips

Voltage Regulator 7805, 7809, 7812

 99.00

A linear regulator is a system used to maintain a steady voltage. The resistance of the regulator varies in accordance with the load resulting in a constant voltage output Because a linear voltage regulator is very common & integral to a number of other elements, regulators ICs are very popular.

Qty: 5 Pcs. each of 7805, 7809, 7812

Buzzer Small 5V

 19.00

5V PCB Mounting Buzzer is a small PCB (printed circuit board) mountable buzzer. It is very small and compact 2-pin structure hence can be easily used on breadboard, PCBs which makes this a widely used component in most electronic applications. This Buzzer module emits loud sound when 3V to 5V is applied to it. Unlike a plain piezo, this buzzer does not need an AC signal. On one hand, that makes it really great for integrating into projects because you don't need an oscillating control signal. But on the other hand, you cannot change the frequency.
 

Buzzer Big 5V

 29.00

5V PCB Mounting Buzzer is a big PCB (printed circuit board) mountable buzzer. It is very big and compact 2-pin structure hence can be easily used on breadboard, PCBs which makes this a widely used component in most electronic applications. This Buzzer module emits loud sound when 3V to 5V is applied to it. Unlike a plain piezo, this buzzer does not need an AC signal. On one hand, that makes it really great for integrating into projects because you don't need an oscillating control signal. But on the other hand, you cannot change the frequency.
 

Diode Pack

 49.00

A diode is a specialized electronic component with two electrodes called the anode and the cathode. Most diodes are made of semiconductor material such as silicon, germanium, or selenium. The fundamental property of a diode is its tendency to conduct electric current in only one direction.

Qty. Pack of 50 diodes.

Push Button Switch

 99.00

A push-button (also spelled pushbutton) or simply button is a simple switch mechanism for controlling some aspect of a machine or a process. Buttons are typically made out of hard material, usually plastic or metal. The surface is usually flat or shaped to accommodate the human finger or hand, so as to be easily depressed or pushed. Buttons are most often biased switches, although many un-biased buttons (due to their physical nature) still require a spring to return to their un-pushed state. Terms for the "pushing" of a button include pressing, depressing, mashing, slapping, hitting, and punching.

Qty: Pack of 100 switches

555 Timer IC

 49.00

The 555 timer IC is an integral part of electronics projects. It a simple project involving a single 8-bit micro-controller and some peripherals or a complex one involving system on chips (SoCs), 555 timer working is involved.These provide time delays, as an oscillator and as a flip-flop element among other applications.The single 555 Timer chip in its basic form is a Bipolar 8-pin mini Dual-in-line Package (DIP) device consisting of some 25 transistors, 2 diodes and about 16 resistors arranged to form two comparators, a flip-flop and a high current output stage as shown below as well as the 555 Timer there is also available the NE556 Timer Oscillator which combines TWO individual 555’s within a single 14-pin DIP package and low power CMOS versions of the single 555 timer such as the 7555 and LMC555 which use MOSFET transistors instead.

Qty: Pack of 10 ICs. 

Atmega 16U2 USB Controller IC

 149.00

The ATmega8U2/16U2/32U2 is a low-power CMOS 8-bit microcontroller based on the AVR enhanced RISC architecture. By executing powerful instructions in a single clock cycle, the ATmega8U2/16U2/32U2 achieves throughputs approaching 1 MIPS per MHz. allowing the system designed to optimize power consumption versus processing speed.

Battery Holder 6 AA with DC Jack

 119.00

A 6 AA is the best suitable power supply option for robotics and embedded system. It comes with DC Jack male connector and is compatible with 6 batteries, the Battery size is AA and provides DC Power supply of 9V and can be directly connected with MehcanzO remote & controller card.

Features 

6 AA Battery Holder with lead wires

Flame Sensor

 249.00

A flame detector is a sensor designed to detect and respond to the presence of a flame or fire, allowing flame detection A flame detector can often respond faster and more accurately than a smoke or heat detector due to the mechanisms it uses to detect the flame.

Battery Holder 4 AA with DC Jack

 89.00

Battery holder 4 AA is best suitable power supply option for robotics and embedded system. It comes with DC Jack male connector which can be directly connected with MehcanzO remote & controller card.

FEATURES:-
•    It is compatible with 4 batteries.
•    Battery size is AA.
•    DC Power supply of 6V can be given at a time.

9V Battery - HIW

 19.00

9V BATTERY CLIPac GENERAL DESCRIPTION. 9-volt battery in its most common form was introduced for the early transistor radios. It has a rectangular prism shape with rounded edges and a polarized snap connector at the top. This type is commonly used in walkie talkies, clocks and smoke detectors.

LEDs - Blue

 99.00

A light-emitting diode (LED) is a semiconductor light source that emits light when current flows through it. Electrons in the semiconductor recombine with electron holes, releasing energy in the form of photons. The color of the light (corresponding to the energy of the photons) is determined by the energy required for electrons to cross the band gap of the semiconductor.

It is pack of 100 LEDs

Touch Sensor Module TTP22X

 149.00

A touch sensor is a type of sensor that captures and records physical touch or embrace on a device and/or object.It enables a device or object to detech touch, typically by a human user or operator. A touch sensor may also be called a touch detector.

9V Battery connector with DC Jack

 19.00

This simple cable has so many uses Plug the battery clip onto a standard 9V battery and connect the other end to any device that needs 9V. The Connector leads are polarity color coded, Red and Black.

FEATURES

• Red and black leads.
• DC power jack

General Purpose PCB (140*90 mm)

 59.00

The material used in PCB from top to bottom includes Silkscreen, Soldermask, Copper and Substrate. The last of those layers, substrate, is made of fiberglass and is also known as FR4, with the FR letters standing for "fire retardant."

General Purpose PCB (80*55 mm)

 39.00

The material used in PCB from top to bottom includes Silkscreen, Soldermask, Copper and Substrate. The last of those layers, substrate, is made of fiberglass and is also known as FR4, with the FR letters standing for "fire retardant." and is 80 x 55mm in lenght.

16x2 LCD

 149.00

LCD (Liquid Crystal Display) screen is an electronic display module and find a wide range of applications. A 16x2 LCD display is very basic module and is very commonly used in various devices and circuits. These modules are preferred over seven segments and other multi segment LEDs. A 16x2 LCD means it can display 16 characters per line and there are 2 such lines. In this LCD each character is displayed in 5x7 pixel matrix. This LCD has two registers, namely, Command and Data.

Features:

• 5 x 8 dots with cursor
• Built-in controller (KS 0066 or Equivalent)
• +5V power supply (Also available for + 3V)
• 1/16 duty cycle
• H/L to be driven by pin 1, pin 2 or pin 15, pin 16 or A.K (LED)
• N.V. optional for + 3V power supply

LEDs - Green

 99.00

A light-emitting diode (LED) is a semiconductor light source that emits light when current flows through it. Electrons in the semiconductor recombine with electron holes, releasing energy in the form of photons. The color of the light (corresponding to the energy of the photons) is determined by the energy required for electrons to cross the band gap of the semiconductor.

It is pack of 100 LEDs

Relay Module (1 relays)

 79.00

A relay is an electrically operated device. It has a control system and (also called input circuit or input contactor) and controlled system (also called output circuit or output cont actor). It is frequently used in automatic control circuit. To put it simply, it is an automatic switch to controlling a high-current circuit with a low-current signal.

The advantages of a relay lie in its lower inertia of the moving, stability, long-term reliability and small volume. It is widely adopted in devices of power protection, automation technology, sport, remote control, reconnaissance and communication, as well as in devices of electro mechanics and power electronics. Generally speaking, a relay contains an induction part which can reflect input variable like current, voltage, power, resistance, frequency, temperature, pressure, speed and light etc. It also contains an actuator module (output) which can energize or de-energize the connection of controlled circuit. There is an intermediary part between input part and output part that is used to coupling and isolate input current, as well as actuate the output. When the rated value of input (voltage, current and temperature etc.) is above the critical value, the controlled output circuit of relay will be energized or de-energized.
NB: input into a relay can be divided into two categories: electrical quantities (including current, voltage, frequency, power etc.) and non- electrical quantities (including temperature, pressure, speed, etc.)

MQ2 LPG Sensor Module

 249.00

This is a simple-to-use Liquefied Petroleum Gas (LPG) Sensor, suitable for sensing LPG (composed of mostly propane and butane) concentrations in the air. The MQ2 can detect LPG gas concentrations anywhere from 200 to 10000ppm .The sensor's output is a measure of the analog resistance & the ouput across the sensing material, Tin Dioxide (SnO₂).

Geared DC Motor(300 Rpm)

 149.00

300RPM Centre Shaft Economy Series DC Motor is high quality low cost DC geared motor. It has steel gears and pinions to ensure longer life and better wear and tear properties. The gears are fixed on hardened steel spindles polished to a mirror finish.The output shaft rotates in a plastic bushing.The whole assembly is covered with a plastic ring. Gearbox is sealed and lubricated with lithium grease and require no maintenance. The motor is screwed to the gear box from inside.
Although motor gives 300 RPM at 12V but motor runs smoothly from 4V to 12V and gives wide range of RPM, and torque

Tables below gives fairly good idea of the motor’s performance in terms of RPM and no load current as a function of voltage and stall torque, stall current as a function of voltage.

Specifications of the product are:-

DC supply: 4 to 12V
RPM: 300 at 12V
Total length: 46mm
Motor diameter: 36mm
Motor length: 25mm
Brush type: Precious metal
Gear head diameter: 37mm
Gear head length: 21mm
Output shaft: Centred
Shaft diameter: 6mm
Shaft length: 22mm
Gear assembly: Spur
Motor weight: 90gms

Water Pump Module

 149.00

This is a low cost mini submersible type water pump that works on 3-6V DC. It is extremely simple and easy to use. Just immerse the pump in water, connect a suitable pipe to the outlet and power the motor with 3-6V to start pumping water it s great for building science projects, fire-extinguishers, fire fighting robots, fountains,waterfalls, plant watering systems. It is small, compact and light. It can be controlled from a micro controller/Arduino using our DC Motor Drivers or one of our Relay Boards. You may use our 5V SMPS Power Supply Adapter to run this pump. You may also use our 6V Solar Panel to run the pump with appropriate a voltage regulator. 

Do not run the pump dry (without putting it in water) and do not use it to pump flammable liquids.

Laser Diode

 49.00

A laser diode, (LD) is a semiconductor device similar to a light-emitting diode in which the laser beam gets generated at the diode's junction.Laser diodes can directly convert electrical energy into light. Driven by voltage, the doped p-n-transition allows for recombination of an electron with a hole. Due to the drop of the electron from a higher energy level to a lower one, radiation, in the form of an emitted photon is generated. This is spontaneous emission. Stimulated emission can be produced when the process is continued and further generate light with the same phase, coherence and wave length.

Features:
•    RoHS (Restriction of Hazardous Substances) Compliant.
•    Quality level is high.
•    Cost is economical.
•    Wavelength from 635 nm to 660 nm.
•    Rise and fall time is 0.5ns. 

Technical Specification:
•    Operating Temperature: -10 ~ +40 ℃.
•    Storage Temperature: -15 ~ +85 ℃.
•    Output power (Po):  5 mW.
•    Normal and maximum operating voltage is 2.2 and 2.7 respectively.
•    Threshold current in minimum, normal and maximum condition are 15, 20 and 30mA.
•    Operating current is 65 to 80mA.
•    Beam Angle deviation: For both parallel and perpendicular condition it is in between -3 to 3 degrees

    Beam divergence:-
•    For parallel condition it is in between 8 to 12 degree.
•    For perpendicular condition it is in between 23 to 32 degree.
 

Piezoelectric Plate

 49.00

A piezoelectric plate is a device that uses the piezoelectric effect to measure pressure, acceleration, strain or force by converting them to an electrical charge. Piezoelectricity is the electricity generated by piezo element by effect called the piezoelectric effect. It is the ability of certain materials to generate an AC (alternating current) voltage when subjected to mechanical stress or vibration, or to vibrate when subjected to an AC voltage, or both. The most common piezoelectric material is quartz. Certain ceramics, Rochelle salts, and various other solids also exhibit this effect. 

Specification:
•    Resonance Frequency: 4.6 KHz +/- 0.5 KHz
•    Resonance Impedance: 200 Ohms
•    Capacitance: 20nF +/- 30% at 1 KHz
•    Operating Temperature -20 to +70 C
•    Storage Temperature -30 to +80 C
•    Metal Material Brass

Qty: Pack of 5 Pcs.

Resistors

 49.00

The box which contains the resistors of different values for estimating and comparing the resistance is known as the resistance box. The accuracy of the resistance box is very high. A resistor is an electrical component that limits or regulates the flow of electrical current in an electronic circuit. Resistors can also be used to provide a specific voltage for an active device such as a transistor. and contains a pack of 100 resistors.

Capacitors

 99.00

The box which contains the capacitors of different values for estimating and comparing the capacitance is known as the capacitance box. A capacitor (originally known as a condenser) is a passive two-terminal electrical component used to store energy electrostatically in an electric field. Unlike a resistor, a capacitor does not dissipate energy. Instead, a capacitor stores energy in the form of an electrostatic field between its plates.

Pack of 100 capacitors.

Hookup wire Roll/ Connecting wire roll

 399.00

Hook-up wire is in the family of lead wires that may be used for low-voltage, low current applications and is a single insulated conductor. Hook-up wire is frequently used in control panels, automotives, meters, ovens, as internal wiring of computers, electronic equipment, business machines and appliances.

Jumper Wires - M-M

 99.00

Jumper wires are simply wires that have connector pins at each end, allowing them to be used to connect two points to each other without soldering. Jumper wires are typically used with breadboards and other prototyping tools in order to make it easy to change a circuit as needed.Male ends have a pin protruding and can plug into things, while female ends do not and are used to plug things into. Male-to-male jumper wires are the most common and what you likely will use most often. When connecting two ports on a breadboard, a male-to-male wire is what you'll need.
 

Jumper Wires - M-F

 99.00

Jumper wires are simply wires that have connector pins at each end, allowing them to be used to connect two points to each other without soldering. Jumper wires are typically used with breadboards and other prototyping tools in order to make it easy to change a circuit as needed.Male ends have a pin protruding and can plug into things, while female ends do not and are used to plug things into. Male-to-female jumper wires are the most common and what you likely will use most often. When connecting two ports on a breadboard, a male-to-female wire is what you'll need.
 

Jumper Wires - F-F

 99.00

Jumper wires are simply wires that have connector pins at each end, allowing them to be used to connect two points to each other without soldering. Jumper wires are typically used with breadboards and other prototyping tools in order to make it easy to change a circuit as needed.
Female ends have a pin protruding and can plug into things, while female ends do not and are used to plug things into. Female-to-female jumper wires are the most common and what you likely will use most often. When connecting two ports on a breadboard, a female-to-female wire is what you'll need.
 

Electronics Tinkering Kit Pro

 1490.00    1341.00

Electronics Tinkering Kit Pro is best suited for students who are Electronics enthusiasts and are interested in learning electronic projects prototyping. It explores the basic concepts of the included electronic components. The kit comprises of all standard components required for hassle free and outcome based learning. Every component included in the kit plays a significant role. The kit includes comprehensive documentation making it easier to understand, learn & build.

Key features of the 'Electronics Tinkering Pro' kit are:-

• The kit contains various electronic components including ICs, Active Elements, Discrete Components & other Elements including IC-555, ICUM-66, ICLM-358, Transistors, Diode 4007, DC Motors, Condenser Mic, Touch Plate.
• A number of projects can be built using this kit viz are Automatic Street Light Controller, Melody Generator, Clap Switch, LED Blinking using Transistor.
• The kit includes comprehensive Documentation explaining the concepts behind every component as well as step by step instructions to use the same.
• The kit conforms to all common safety & environmental standards, is completely safe to use.

Components included in the kit:-

• IC 555
• IC UM66
• IC LM358
• Transistors - BC547 & 557
• Diode 4007
• DC Motor
• Condenser Mic
• Touch Plate (Piezo Disc (thin))
• LDR
• Speaker 8Ohm
• 15cm Single-Strand Wire Antenna
• Variable Resistor 10KOhm
• Resistors - Different Values 
• Ceramic Capacitor - 104
• Electrolytic Capacitors 
• Push Button Switches
• LED - Red
• Buzzer
• Breadboard
• Battery - 9V
• Battery Cap + Lead

Electronics Tinkering Kit Pro+

 1790.00    1500.00

Electronics Tinkering kit pro+ is an Advanced-level kit for Electronics & STEM Enthusiasts for learning Electronics prototyping & advanced projects building students can learn advanced level integration of different ICs, Active Elements, Discrete Components and other elements not covered in the Pro tinkering kit Students can do some serious self-paced higher level learning using this tinkering kit, with comprehensive Documentation provided that eases the process a great deal diving into the concepts of every component, besides step-by-step instructions on the use of the same.

Key features of the 'Electronics Tinkering Pro+' kit are:-

• The kit contains a number of electronic components including various types of ICs, Transistor BC547, Diode 4001, Diode 4007, Temperature Sensor - LM35, a Touch Plate (Piezo disc (thin)), a 7-Segment LED Display, an IR Transmitter & Receiver, a Condenser Mic, DC Motors..
• A whole lot of electronic circuits & projects can be built using the provided components, viz. LED Blinking using a Timer, Touch-on-Touch-off Switch, Object Detector using IR Sensor, LED Bar Graph.
• Includes comprehensive Documentation explaining the concept(s) behind every component as well as step-by-step instructions on how to use the same in building prototypes.
• The kit conforms to all common safety & environmental standards, is completely safe to use.

Components included in the kit are:-

• IC 555 - Timer
• IC LM358 - Diff. Opamp
• IC LM35 - Temp Sensor
• Transistor - BC547
• Diode - 4001
• Diode - 4007
• DC Motor
• Condenser Mic
• Touch Plate (Piezo Disc (thin))
• LDR
• Speaker - 8Ohm
• Small Fan Blade
• Variable Resistor - 10KOhm
• Resistors - Different Values 
• Ceramic Capacitor - 104
• Capacitors - Different Types & Values 
• Push Button Switches
• LED - Red, Yellow
• Buzzer
• Breadboard
• Battery - 9V
• Battery Cap + Lead

Breadboard - 800 Points

 89.00

A breadboard is a solderless device for temporary prototype with electronics and test circuit designs. Breadboards are used for rapid prototyping of electronic projects, without needing to solder the components to make it work. Most electronic components in electronic circuits can be interconnected by inserting their leads or terminals into the holes and then making connections through wires where appropriate. The breadboard has strips of metal underneath the board and connects the holes on the top of the board.

This is a Full size breadboard or standard size breadboard with 800 tie points, the breadboard measures 55mm x 170mm, you can combine two or more of this breadboard to make larger or wider breadboards, it also includes an adhesive foam at the back, to mount it securely on most surfaces.

RGB LEDs

 99.00

RGB LED means red, blue and green LEDs. RGB LED products combine these three colors to produce over 16 million hues of light. Note that not all colors are possible. Some colors are outside the triangle formed by the RGB LEDs also, pigment colors such as brown or pink are difficult, or impossible, to achieve. RGB LED is a combination of three LEDs in just one package: red, green and blue. You can generate different colors by adjusting the brightness of each of the three LEDs of the RGB LED; to adjust the brightness of each LED, you use a PWM signal.

Seven segment LED Display - 4 Digit

 199.00

A seven-segment display (SSD), or seven-segment indicator, is a form of electronic display device for displaying decimal numerals that is an alternative to the more complex dot matrix displays. Seven-segment displays are widely used in digital clocks, electronic meters, basic calculators, and other electronic devices that display numerical information.Each of the seven LEDs is called a segment because when illuminated the segment forms part of a numerical digit (both Decimal and Hex) to be displayed. An additional 8th LED is sometimes used within the same package thus allowing the indication of a decimal point, (DP) when two or more 7-segment displays are connected together to display numbers greater than ten.

FEATURES:
•    Available in two modes Common Cathode (CC) and Common Anode (CA)
•    Low current operation
•    Current consumption : 30mA / segment
•    Peak current : 70mA

Bread Board - 400 points

 89.00

Solderless breadboards are commonly used for prototyping because they allow you to quickly build temporary circuits without soldering. Breadboards accept most through-hole parts and up to 22 wire. When you’re done or want to change your circuit, it’s easy to take your circuit apart. Pre-cut and premium jumper wires are especially convenient for Solderless Breadboard.Two sides of the breadboard have tabs and the other two sides have compatible slots, which lets you connect multiple 400-point breadboards for more prototyping space.

Specifications:

• It has total 400 holes
• Perfect for electronics protype experiments
• After experimenting with breadboards you can make your circuit more permanent with same connection
• Made up of ABS plastic + Phosphor bronze nickel plated spring clips.

LEDs - Yellow

 99.00

A light-emitting diode (LED) is a semiconductor light source that emits light when current flows through it. Electrons in the semiconductor recombine with electron holes, releasing energy in the form of photons. The color of the light (corresponding to the energy of the photons) is determined by the energy required for electrons to cross the band gap of the semiconductor.

">

LEDs - White

 99.00

A light-emitting diode (LED) is a semiconductor light source that emits light when current flows through it. Electrons in the semiconductor recombine with electron holes, releasing energy in the form of photons. The color of the light (corresponding to the energy of the photons) is determined by the energy required for electrons to cross the band gap of the semiconductor.

Button Switch Set

 799.00

A push-button (also spelled pushbutton) or simply button is a simple switch mechanism for controlling some aspect of a machine or a process. Buttons are typically made out of hard material, usually plastic or metal. The surface is usually flat or shaped to accommodate the human finger or hand, so as to be easily depressed or pushed. 

Capacitive Touch Switch Module

 99.00